::: Kits :::
New Products Specials Dollar Store 3D PRINTING ANTI-STATIC PRODUCTS ARDUINO/RASPBERRY Robotics PROJECT LEAD the WAY TEACHERS CLASSPACKS TRAINING-Ohm's Law DVD'S Educational Accessories Alarm/Automotive App Kits Alternative Energy Audio/Hi Fi Application Kits Black Light Kits Batteries Breadboards CAMERAS/Infra-Red Calculators Car Kits Cases for Kits Cold Cathode Lamps Closed Circuit TV / CCTV Computer Accessories Components Computer Equipment Printer Cartridges Lego Consumer Products Educational Kits Electronic Project/Lab Kits Engino Kits Fiber Optic Kits/Equipment FUEL CELL KITS Geiger Kits Globes Home Application Kits Hexbugs Infrared/Laser Kits Interface Systems Kits Laser Kits/Infrared Learn to Solder Kits LED Kits Light Application Kits Magnifying Lamps Measuring Instrument Kits Microscopes Mini Soldering Kits Module Kits Mounted Kits/Assembled Multimeters (Assembled) Multimeter Kits MUSIC Non Soldering Kits Oscilloscopes OWI Robots Parallax Programming Products Power Supplies (Assembled) Power Supply Kits/Charger Kits Printed Circuit Products Quiz Bowl Kits Radio Kits Transmitters and Receivers Remote Control Unit Kits Robotic Arms Kits/Accessories Robotic Kits/Non Soldering Robot Kits - Soldering Safety Products Science Tech Discovery Planet Science Equipment and Toys Science/Physics/Spectrum Tubes Science Project/Lab Kits Season/Holiday Kits Security Products Snap Circuits Snooper Kits Software Solar Kits/Accessories Solder Soldering Equipment Soldering Kits in Cases Sound & Light Kits Strobe Light Kits Surface Mount Kits Test Equipment (Assembled) Test Equipment Kits Test Leads Thames and Kosmos Timer & Controller Kits Tools Tool Kits/Cases/Storage Toys Trainers/Microcontrollers Tree of Knowledge Velleman Products Video Application Kits Videos Wire/Cable Wooden Kits Xeltek Programmers
Categories
|
Omnitron Electronics Toll Free:1-800-379-6664 Phone:954-574-0345 Fax: 954-574-9528
|
Product Details
|
VELLEMAN ARDUINO T020010 TINKERKIT SENSOR SHIELD, V2, MODULE
SKU: ARD-T020010
|
Overview
Product Details
ARDUINO T020010 TINKERKIT SENSOR SHIELD, V2, MODULE
The Sensor Shield v.2 allows you to hook up the TinkerKit sensors and actuators directly to the Arduino, without the use of the breadboard.
It has 12 standard TinkerKit 3-pin connectors. The 6 labelled I0 through I5 are analog inputs. The ones labelled O0 through O5 are analog outputs connected to the PWM-capable outputs of the Arduino board (it is possible to change these to digital inputs, in which case they will report either high or low, but nothing in between).
On a standard Arduino DuemilaNove board the pins are:
- Pin 11 on the Arduino is O0 on the shield.
- Pin 10 on the Arduino is O1 on the shield.
- Pin 9 on the Arduino is O2 on the shield.
- Pin 6 on the Arduino is O3 on the shield.
- Pin 5 on the Arduino is O4 on the shield.
- Pin 3 on the Arduino is O5 on the shield.
Module description: A green LED signals that the shield is correctly powered, a standard 6 mm push button allows you to reset the board.
The 4-pin TWI socket allows communication to any device supporting the I2C protocol through the Wire library on Arduino. 5 V and ground are provided on the socket. Note that on Arduino the I2C bus uses analog inputs 4 and 5, using the TWI connection precludes the use of those analog inputs.
The 4-pin SERIAL socket allows the board to communicate with other devices that support serial communication. 5 V and ground are provided on the socket for your convenience.
Note: If you are sending or receiving data to and from the computer, this serial connector is not available.
Two mounting holes are provided in the same position found on the Arduino board. A third hole allows you to see the LED connected to pin 13 of the Arduino.
On a standard Arduino DuemilaNove board the pins are:
- Pin 11 on the Arduino is O0 on the shield.
- Pin 10 on the Arduino is O1 on the shield.
- Pin 9 on the Arduino is O2 on the shield.
- Pin 6 on the Arduino is O3 on the shield.
- Pin 5 on the Arduino is O4 on the shield.
- Pin 3 on the Arduino is O5 on the shield.
Module description: A green LED signals that the shield is correctly powered, a standard 6 mm push button allows you to reset the board.
The 4-pin TWI socket allows communication to any device supporting the I2C protocol through the Wire library on Arduino. 5 V and ground are provided on the socket. Note that on Arduino the I2C bus uses analog inputs 4 and 5, using the TWI connection precludes the use of those analog inputs.
The 4-pin SERIAL socket allows the board to communicate with other devices that support serial communication. 5 V and ground are provided on the socket for your convenience.
Note: If you are sending or receiving data to and from the computer, this serial connector is not available.
Two mounting holes are provided in the same position found on the Arduino board. A third hole allows you to see the LED connected to pin 13 of the Arduino.
Photos
|
|
|
Tell a Friend
Cart Contents
Order Info
TOLL FREE: 800-379-6664
INTERNATIONAL:954-574-0345
SCHOOL PURCHASE ORDERS:
FAX: 954-574-9528
INTERNATIONAL ORDERS:
MONEY ORDER,WESTERN UNION, OR BANK WIRE
(NOT INCL. CANADA)
INTERNATIONAL:954-574-0345
SCHOOL PURCHASE ORDERS:
FAX: 954-574-9528
INTERNATIONAL ORDERS:
MONEY ORDER,WESTERN UNION, OR BANK WIRE
(NOT INCL. CANADA)
Sale Item
Powered by SunShop "Shopping Cart Software"