::: Kits :::
New Products Specials Dollar Store 3D PRINTING ANTI-STATIC PRODUCTS ARDUINO/RASPBERRY Robotics PROJECT LEAD the WAY TEACHERS CLASSPACKS TRAINING-Ohm's Law DVD'S Educational Accessories Alarm/Automotive App Kits Alternative Energy Audio/Hi Fi Application Kits Black Light Kits Batteries Breadboards CAMERAS/Infra-Red Calculators Car Kits Cases for Kits Cold Cathode Lamps Closed Circuit TV / CCTV Computer Accessories Components Computer Equipment Printer Cartridges Lego Consumer Products Educational Kits Electronic Project/Lab Kits Engino Kits Fiber Optic Kits/Equipment FUEL CELL KITS Geiger Kits Globes Home Application Kits Hexbugs Infrared/Laser Kits Interface Systems Kits Laser Kits/Infrared Learn to Solder Kits LED Kits Light Application Kits Magnifying Lamps Measuring Instrument Kits Microscopes Mini Soldering Kits Module Kits Mounted Kits/Assembled Multimeters (Assembled) Multimeter Kits MUSIC Non Soldering Kits Oscilloscopes OWI Robots Parallax Programming Products Power Supplies (Assembled) Power Supply Kits/Charger Kits Printed Circuit Products Quiz Bowl Kits Radio Kits Transmitters and Receivers Remote Control Unit Kits Robotic Arms Kits/Accessories Robotic Kits/Non Soldering Robot Kits - Soldering Safety Products Science Tech Discovery Planet Science Equipment and Toys Science/Physics/Spectrum Tubes Science Project/Lab Kits Season/Holiday Kits Security Products Snap Circuits Snooper Kits Software Solar Kits/Accessories Solder Soldering Equipment Soldering Kits in Cases Sound & Light Kits Strobe Light Kits Surface Mount Kits Test Equipment (Assembled) Test Equipment Kits Test Leads Thames and Kosmos Timer & Controller Kits Tools Tool Kits/Cases/Storage Toys Trainers/Microcontrollers Tree of Knowledge Velleman Products Video Application Kits Videos Wire/Cable Wooden Kits Xeltek Programmers
Categories
|
Omnitron Electronics Toll Free:1-800-379-6664 Phone:954-574-0345 Fax: 954-574-9528
|
Product Details
|
VELLEMAN MLP106 MadLab ELECTRONIC DIY KIT- Lie Detector
SKU: MLP106
|
Overview
Product Details
LIE DETECTOR DIY KIT - solder version
Product Features:
The Lie Detector works by measuring galvanic response. In other words, when a person lies, they tend to sweat. Perspiration has a high sodium content, so sweat is conductive. Dry skin has a resistance of about 1 million ohms, whereas the resistance of moist skin is reduced by a factor of ten or more.
A person holding the probe wires will change the voltage at the upper probe wire depending on their skin resistance. The skin resistance is in parallel with R2 and, because it is likely to be similar to or smaller than R2, the voltage at the probe wire will fall as skin resistance falls.
A person holding the probe wires will change the voltage at the upper probe wire depending on their skin resistance. The skin resistance is in parallel with R2 and, because it is likely to be similar to or smaller than R2, the voltage at the probe wire will fall as skin resistance falls.
Skill Level 2. This kit requires soldering of components to the PC board while building.
- This kit requires soldering of components to the PC board while building.
- Soldering required
- Ages 13+
Product Specifications:
The circuit diagram of the Lie Detector is shown below. It consists of three transistors (TR1 to TR3), a capacitor (C1), two lights or LEDs (L1 & L2), five resistors (R1 to R5), and a variable resistor (VR1). Suitable transistors to use are BC547, BC548 or BC549, or any other small NPN transistor.
This circuit is based on the fact that a person's skin resistance changes when they sweat (sweating because they're lying). Dry skin has a resistance of about 1 million ohms, whereas the resistance of moist skin is reduced by a factor of ten or more.
Resistors R1 and R2 form a voltage divider. They have resistances of 1 000 000 ohms (1 mega ohms) and, because their values are equal, the voltage at the upper probe wire is half the battery voltage (about 4.5 volts).
A person holding the probe wires will change the voltage at the upper probe wire depending on their skin resistance. The skin resistance is in parallel with R2 and, because it is likely to be similar to or smaller than R2, the voltage at the probe wire will fall as skin resistance falls.
Capacitor C1 functions as a smoothing capacitor and removes the 50Hz induced mains hum that is found on a person's body.
TR1 and R3 form a buffer circuit (called an emitter-follower). The voltage at the emitter of TR1 follows the voltage at the probe wire and is now able to drive transistor TR2.
Transistors TR1 and TR2 act as a voltage comparator. If the voltage at the base of TR2 is higher than at the base of TR3 then the green LED (L1) will come on. If the reverse is true then the red LED (L2) will light.
To test the Lie Detector hold the probe wires. Adjust VR1 until the green LED is just on and the red LED is just off. This is the point at which the voltage at the base of TR2 is just greater than at the base of TR3. Now use moist fingers to hold the probes. This lowers the skin resistance and causes the voltage at the base of TR2 to fall. The voltage at the base of TR3 is now greater and the red LED comes on.
Tell a Friend
Cart Contents
Order Info
TOLL FREE: 800-379-6664
INTERNATIONAL:954-574-0345
SCHOOL PURCHASE ORDERS:
FAX: 954-574-9528
INTERNATIONAL ORDERS:
MONEY ORDER,WESTERN UNION, OR BANK WIRE
(NOT INCL. CANADA)
INTERNATIONAL:954-574-0345
SCHOOL PURCHASE ORDERS:
FAX: 954-574-9528
INTERNATIONAL ORDERS:
MONEY ORDER,WESTERN UNION, OR BANK WIRE
(NOT INCL. CANADA)
Sale Item
Powered by SunShop "Shopping Cart Software"